Dynamix RC 903-V35FE1 User Manual

RRCC 990033--VV3355FFEE11 VV..3355 ttoo FFrraaccttiioonnaall EE11 IInntteerrffaaccee CCoonnvveerrtteerr User Manual

4.2. Back panel Sketch of the back panel of AC equipment Sketch of the back panel of DC equipment Power interface: AC interface:

Send Data (B) — TD(B) I S Send Timing (A) — TCK(A) O Y Send Timing (B) — TCK(B) O AA Terminal Timing (A) — SCTE(A) I U Terminal Timing (B)

1st bit 2nd bit 3rd bit 4th bit 5th bit 6th bit 7th bit 8th bit Definition Timing Clock 1 Timing clock2 TS_FLOW Time slotfollow BERT

OFF OFF Master clock (internal timing) OFF ON ON OFF V.35 Terminal clock ( followV.35 interface timing ) ON ON Slave clock (followE1 line timi

which means that it has receive the correct test bit. If you choose to set the loop-back of the remote E1 line RLOOP, it means testing the whole pr

Local Converter Local Converter Remote Converter Local Converter Remote Converter 5.6th 7th and 8th bit: selecting switch of the loop-back

5th bit 6th bit 7th bit 8th bit 5th bit 6th bit 7th bit 8th bit ON ON ON ON OFF OFF OFF OFF 2) There is no PCM equip

5th bit: sending side ‘TX-grounded; 6th bit: receiving side ‘RX-grounded; 7th bit: impedance adjustment at the receiving side 8th bit: impedanc

4.5. Basic Connection The topological figures here are just for reference, users can design it according to practical application. The figure

When using “Master Clock — Slave Clock” connection structure, if DXC and MUX devices are connected in series in E1 link, then DXC,

1. Cautions Warning . Only trained and qualified personnel should be allowed to install, replace or service thi

other manufactures. ADM If Routers with E1 interface are used at remote side, users are required to first confirm all the paramet

5. Equipment installation and Preparation 5.1. Installation preparation  Make sure that the E1 line cable matches the equipment model con

polarity is strictly forbidden.  When the equipment is on power and there is no equipment connecting to the V.35 interface, the AIS indicator is

6. Troubleshooting If there are any problems during installation and operation, please try to solve them according to the

 Compatibility with other V.35 Dynamix products Answer: RC903-V35FE1 and RC904-V35FE1 can cooperate with other Dynamix products th

Router DTE ISO2593Femal interface M34 Female interface Standard V.35 Name ISO2593 Male interface M34 male interface A PGND A P TD(A) P R RD

Converter. Converter DCE Node DCE CBL-V35-M34M/M34M-X-D Customer DTE Cable This cable is for the clients who have the need of cros

Contents 1. Cautions... 1 2. O

2. Overview 2.1. Introduction RC 903-V35FE1 is an interface converter for V.35 equipment based on E1 network transmission. Wi

RC903-V35FE1-DCStandalone , one E1 interface ( 75Ω unbalanced or 120Ω Balanced), one standard V35 DCE interface (ISO2593 M34 Fem

3. Parameters 3.1. E1 interface: Input impedance: Two 75Ω (unbalanced BNC interface) and one 120Ω (balanced RJ-45 interface) Interface bit

3.5. Structure: Standalone Dimensions: 120(W)*39(H)*155(D) mm 3.6. Ambience Operation temperature: 0~45°C Operation humidity: ≤90% (25 °C)

4. User Manual 4.1. Front panel Power Indicator: Sketch of the front panel Power (PWR): On: power is working in good condition Off: Pow

E1 interface alarm Indicator: LOS red: On: loss of receiving signal at local E1; Flashing: loss of receiving signal at remote E1 (only effective a