Dynamix DW FXS-04 User's Guide

DW 2522 User Guide DYNAMIX

10Step 6: Setup each FXS line’s parameters by clicking the Line ID from FXS settings > FXS Line. Modify the SIP register information and apply it.

11 Step 8: After soft-reset or reboot, Click Line Status to check registration status. (Fig.8) (Fig.8) following features: For FXO: (2 stage

12Device Settings From this setting category, all devices related to parameters can be found here. Network Configuration > Network Param

13 VOIP VLAN: Enable VOIP VLAN or not. When enable VOIP VLAN, the WAN port can be only accessed by VLAN. If it is required to manage the instead. 

14Device Time Setting: Device Setting > Time Parameter Description:  Current Time: Current Time, date and year display.  NTP Time Server:

15Device Advance Setting: > Advance Parameter Description:  HTTP Port: The Administrator Web service port (the default is 80)  HTTPS Port:

16User Login Setting: Three level of users can be used, administrator, supervisor, user. Each level of users has different predefined access level.

17Debug Settings: interface. It generates the debug information based on debug level and modules. Since the generating debug will co

18> Event Notice 1. Register Failure or re-registered 2. FXO RJ-11 cable was plugged or unplug 3. Ethernet reconnected 4. System started

19 Select 9510: (This feature is not yet available now. Please don’t select at present) Parameter Description: (This function is not available ye

2Contents Introduction ... 3 Physical Interface ...

20Select Http: This feature is ready to use now.  Http Configuration: Enable or Disable  Http Config URL: internal used only  Refresh i

21 Specify an IP Address: Only the IP address listed can retrieve the SNMP information. Normally, it will be the SNMP manager’s IP address.  Spec

22  PabxMode: Enable or Disable PABX mode, default is Enable. NAT Setting bridge mode. Here is the setting for NAT related service. > DHCP Srv.

23  UPNP Server : Enable UPNP server or not. > Bandwidth (Bandwidth Control) By using bandwidth control feature, the user can manage the traffic

24  specific :  priority 1 – Download: highest priority download bandwidth  priority 2 – Download: normal priority download bandwidth  prior

25IP Target  Priority: Priority value for the target  Type: The target type is set to IP  Configure Type: unique IP or a range of IP addre

26  Priority: Priority value for the target  Type: The target type is set to port number  Configure Type: unique port number or a range of port

27 Type: DSCP value  DSCP: The DSCP will be mapped to the priority > URL Filter  URL Filter: the specified URL will be blocked >

28> MAC Filter  MAC Filter: The MAC address to be blocked, please follow these formats of picture. > APP Filter  APP Filter: app

29 Port Filter: port number or range to be blocked > Port Fwd  Port Fwd: enable port forward feature or not  Port Range: Starting and sto

3Introduction gateway. 1-WAN/1-LAN (management port) 10/100 base-T network environment. Field-proven quality of Voice communication and

30VOIP Parameters Setting SIP Parameters: VOIP Setting > SIP Parameter Description:  Session Timer: Enable session timer or not (RFC 40

31> Audio  Codec 1~5: The preference codec priority  G.711u Payload Size: G.711 u-Law payload size  G.711a Payload Size: G.711 A-law p

32Disable: Send silence packets as normal voice packet (no silence detection)  RTP Basic Port: The RTP starting port. Each channel will be added a

33> NAT Traversal situated behind router.  NAT Traversal:  Disable: Disable NAT traversal features  STUN (Type 1,2): Enable STUN for NA

34VOIP Advance: SIP > Parameter Description:  SIP Hold Type: SIP on hold message sending method. - Send Only: Set the SDP media to send

35is used, general requests are retransmitted at an interval which starts at T1 and doubles until reaches T2. If a provisional response is received,

36subscribe. The default is 600 sec. If a new voice mail is arrived, the stutter tone will be used instead of regular dial tone. This feature is dedi

37Audio> The setting page includes the device related to audio settings.  RFC 2833 Payload Type: 96 or 101. It is recommended to use 101. 

38Ring> The ring cadence, voltage and frequency were configured to the phone.  Frequency (10~70HZ): Specify the ringing frequency value (defau

39Dialing Plan: General>  First Digit Time Out: Specify the duration of the first digit to be dialed when the FXO port was OFF Hook

4IP Network connection IPv4 (RFC 791)/IPV6 (RFC 2460) IPv6 Auto Configuration (RFC 4862) MAC Address (IEEE 802.3) Static IP DHCP Client (RFC 2131) PP

40  Dialed Prefix: The prefix to be matched  Max Digits: The digits will be received based on the Dialed Prefix. The following is an example for

41Digit Manipulation> The Digit Manipulation (DM) will be processed based on prefix and DM group after the DNIS ( Called Party ) was determined.

42Phone Book> Phone Book is used for peer to peer call. Now the feature just supports FXS dialing out, not supports FXO out going call.  Name:

43FXS Setting: The FXS line setting includes each line number and SIP proxy settings.  Line ID: FXS line (TEL 1 to TEL 2)  State: The line is a

44 Line Type: FXS or FXO (depend on device model).  Line State: Set to active if you would like to use this line. Otherwise, set to Inactive. 

45send register message out, the FXS line still can use SIP trunk for VOIP call or call locally.  TEL No: The registrar telephone number  User

46 SIP Proxy> The SIP proxy server defined here is dedicated used for FXS lines.  Domain: The SIP domain for register or call making  Prim

47 Caller ID> The call ID send to FXS port of analog phone set to display caller name or phone number.  Caller ID Mode: Caller ID mode to be u

48 Others> Flash time and current drop generation/detection time  Min flash time(80~800msec): Specify the value of the flash low time, If

49FXO Setting: The FXO Setting contains the FXO related parameters.  Line ID: FXO line (Line 1 , Line 2)  State: The line is active or not 

5Front Panel: LED Indicators LED Description Power When the power adapter is connected, the LED will light up green. Status When system star

50Inactive.  TEL NO: This field can be used as a reference remark for this line. Normally, you can put the connected PSTN line’s phone number he

51 PSTN Answer Ring Count: This ring count is used for called ID detection and 2 stage dialing.  If the caller ID is sending b

52Create SIP Trunk>  Trunk ID: SIP trunk ID 1-4  Register Type: Whether this account need register or not REGISTER message to SIP proxy ser

53No set on FXO lines. -User ID: The SIP caller ID will be used according to the following type.  SIP user ID: If the SIP user ID is set

54 Route Plan: incoming call type, destination, length and prefix code to determine the outgoing call routes and process. There are three routes to g

55 Matched Length: matched DNIS (called number) length. The zero (0) mean no limitation of length.  Outgoing Type: The outgoing call from FXS por

56  Incoming Call Type: Incoming call type  VOIP: The incoming SIP call type  FXS: The FXS extensions incoming call type  Matched Prefix:

57Create Route Plan>Backup Route  Backup Route Active: Active the backup routes or not.  Outgoing Type: Define backup routes outgoing call ty

58 For Non-PABX Mode Interface> For this interface, it could be routed to VOIP and FXO and FXS and vice versa. You can ignore the routing plan if

59 Incoming Call Type: Incoming call type  VOIP: The incoming SIP call type  FXO: The PSTN incoming call type  FXS: The FXS outgoing call t

6Rear Panel: Item Description Reset Press and hold over 5 seconds to reload factory default setting, this action will erase all existing set

60= 282265699) to make call. When backup route is started, the DNIS is still unchanged as 886282265699. This makes the DM easy to predict and impleme

61 States: Device States>  Model: The model number  Network Type: The Network Interface Type Settings  IP-Address: IP address is usi

62 SIP Trunk States>  Account: SIP trunk account  Registered: The SIP trunk register status  Concurrent Call: The concurrent calls are us

63 Maintenance: device.  Backup: Backup the system settings for restoring purpose  Restore: Restoring the backup setting to this device  Re

64 Appendix A --- Call Processing Flow (Dynamix FXS-04)

65Appendix B --- System Recovery you will not encounter the system failed to reboot issue. Normally, the user should be able to use Web page to login

66 - download the firmware into the same file folder or directory with TFTP program. 6. In the Telnet terminal, do the following command

67Appendix C --- HTTP auto provision Get the HTTP provision packet from Welltech and start the provision as follows: Step 1: Build mac list for mass

68Encrypt=0 Step 4: Generate the individual configuration file. Double click the “wtgencfg.exe”, it will generate the configuration file for each MA

7QUICK SETUP Login : 2522 and connect the Ethernet cable to WAN or LAN port. Start Windows IE6.0 typing the default URL which is http://192.168.12

8 Fig.2 Change Default IP Network: Step 3: After successfully logon to the system, we need to change the network configuration. Click

9Change Default Time setting: Step 4: When re-login to the new IP address, the next step is to setup the system time zone. Click Device Setting >